You want to control your Yamaha Soundbar with a universal remote. In that case, you need to set up your favorite universal remote using one of the below codes.
After the code lists, you will find step by step instructions on programming your universal remote using the codes provided and two alternative methods in case that did not work.
If a code does not seem to work, try with another one. We are constantly updating our lists with new codes.
Related links:
Yamaha Blu-ray Player universal remote codes
Yamaha Soundbar Universal Remote Codes
31947, 31331, 30176, 31176, 30354, 10030, 10797, 10017, 10019
Xfinity Remote Code For Yamaha Sound Bar
992
Note: to use this code follow below mentioned code search method.
By using the above mentioned remote codes you can program the remote with your Yamaha Soundbar. You can find the steps for how to program your remote to work with the Soundbar. So check the steps below.
How to program a universal remote to work with a Yamaha Soundbar
Use the below method for Yamaha Soundbar (codes 30176 or 31331)
(There has to be a TV code programmed to the TV device or the volume keys will not work)
- AV1 or AV2
- Press and hold the MUTE & SELECT, you need to wait here for two blinks and then release it
- Now enter 30176 and then AV1 or AV2
- Now Press and Hold Mute & Select again wait for two blinks and then release it
- Now Enter 993 code
- Press Select
- Then AV1 or AV2
- Now press & Hold Mute & Select then wait here for two blinks and then release it
- Now enter 963
- Press CH Down
- Now you need to enter the commands from the directv att remote control.
Or you can use the below method too….
Use code 30176 or 31331 for the Yamaha Sound bar
(There has to be a TV code programmed to the TV device or the volume keys will not work)
- AV1 or AV2
- Press and hold MUTE & SELECT until it gives 2 blinks
- Enter 993 code
- Hit on SELECT
Actually the above mentioned codes can also be used for programing the yamaha soundbar models. The models are:
ATS-1030, YSP-1000, YSP-5100, YSP-4100, YSP-1400, YAS-101, YAS-103, YHT-S400, and YSP-4000BL
Those codes have been tested with the following devices:
Comcast remote controls, Xfinity XR5, DVR 3 device remote, XR2 Remote, Xfinity XR2 U2, XR2 R2, DirecTV, Directv HR24 STB, S10-S4, U-verse remote control, RC65, Satellite H20 Receiver, DirecTV Plus HD DVR, Comcast 3-in-1 remote, and 1067BG3.
There are three simple ways to set up or configure a universal remote to work with your Yamaha Soundbar. Now we are going to guide you step by step on each one of them.
How to program a universal remote to work with your Yamaha Soundbar using a code
The first method is using a keycode. With the correct code, you can program the universal remote to work with your Yamaha Soundbar. The keycode identifies the brand and model of your device.
- The first step is to turn the Yamaha Soundbar you want to configure ON.
- Then we press the TV button on your Universal Remote.
- Next, we need to press and hold the SETUP button of the Universal Remote until we see a light indicator flashing. (When the universal remote does this, it means that it has entered the Learning mode)
- Now you have to enter the code, which you can find on this website or on the instructions of the device you want to configure.
- Once you have entered the code, point the universal remote at the Yamaha Soundbar and press and hold the power button.
- When the screen switches off, then you can release the power button.
If you have followed the steps, now your Yamaha Soundbar will work with the universal remote. If your Yamaha Soundbar is not working, repeat the steps using another code.
How to program a universal remote to work with your Yamaha Soundbar using the code search function
Suppose you weren’t able to find a working code for your Yamaha Soundbar. In that case, there is another method that you can try to set up your universal remote correctly. That method uses the universal remote search function to get the correct code.
- First, you need to turn the Yamaha Soundbar you want to control ON. (Note: You must keep the remote control aimed at the component throughout the process.)
- On the universal remote, press and hold the CODE SEARCH button. When the indicator light illuminates, release the CODE SEARCH button.
- After that, press and release the device button corresponding to the type of device you want the universal remote control to operate.
- Now we should see an indicator light blink once and remain lit.
- Aim the remote control at the Yamaha Soundbar and press and release the POWER ON-OFF button.
- Immediately right after the Yamaha Soundbar turns off, you have to press and release the ENTER button.
- If you do not press the ENTER button within three seconds, the remote control will send the next code in the list, and you will be required to start over from Step 2.
If you have done the procedure correctly, you should already have your Yamaha Soundbar working with the universal remote. When you find a working code using the method described, you can use the code retrieval function to identify the code for your device for future reference.
How to program a universal remote to work with your Yamaha Soundbar using the manual setup
If none of the other methods has worked for you, you can still use the Manual Set up to configure the universal remote.
- First, you need to point your universal remote towards the remote control of the Yamaha Soundbar you want to replace.
- Next, you need to press the SETUP button or MAGIC button, depending on the universal remote you have.
- Now you need to enter the code for manual programming that you can find on your universal remote instruction booklet.
- Next, you need to press a function to program on the universal remote, like TV VOLUME DOWN.
- Then you need to press and hold the corresponding button on the original remote of the Yamaha Soundbar you are programming.
- After that, we should see a light blinking. That means that this function has been saved correctly, and we can use TV VOLUME DOWN on our universal remote.
You would need to repeat the above steps for every function you want to use with the universal remote. You have to press the SETUP button to let the universal remote know that you are done programming when you have finished.
This method copies the IR signal of your original remote to the universal remote, and you rarely would have to use it as usually the other methods should work.
Final Words
We have presented an extensive list of codes for your universal remote. We have also guided you step by step through the many methods to program your universal remote.
We hope the universal remote codes and the programming methods have worked for you.
If you have another device, you can use the search on the top bar to find it. Alternatively, you also can go to our homepage and navigate the categories or brands to find them.
We are glad to have helped you.